PIONEER AMPLIFIER
- 2,000 Watts Max Power
- 5 CAHNNEL. CAN.
- High Quality Textured Flat Panel and Tough Frame
- Variable High-Pass and Low-Pass Filters
- Bass Boost Remote included
Pioneer Amplifier
- Home
- Pioneer Amplifier
PIONEER AMPLIFIER
- Type: car amplifier
- Watts Max Power : 1600
- Length : 215 mm
- Width: 252 mm
- Height: 60 mm
- Channels: four-channel
- Rated power (4 Ohm): 520 W
- Power of channel 1 (4 Ohm): 130 W
- Power of channel 2 (4 Ohm): 130 W
- Power of channel 3 (4 Ohm): 130 W
- Power of channel 4 (4 Ohm): 130 W
- Ability to work at 2 Ohms: +
- Ability to work at 1 Ohms: +
- High-level input: +
- Built-in crossover: +
- Impedance: 4 Ohm
- Sensitivity: 95 dB
- Frequency range from: 10 Hz
- Frequency range up to: 50 Hz
- Amplifier class: D
PIONEER AMPLIFIER
- 2-Channel amplifier
- 25A ATO fuse (installed)
- Speaker input harness with four 4″ wires
- 4 Self-tapping screws (3/4″ length)
- Owner’s Manual (Eng/Fren)
- Owner’s Manual (Span)
- Warranty sheet 2-channel car amplifier
- 60 watts RMS x 2 at 4 ohms (95 watts RMS x 2 at 2 ohms)
- 190 watts RMS x 1 in bridged mode (4-ohm stable in bridged mode)
- Class AB amp technology
- selectable low-pass filter (80 Hz, 12 dB per octave)
- preamp and speaker-level inputs
- fuse rating: 25A x 1
- 10-gauge power and ground leads recommended — wiring and hardware not included with amplifier
- 9-3/4″W x 2-3/8″H x 7-3/16″D
PIONEER AMPLIFIER
- 500 watts RMS x 1 at 4 ohms (800 watts RMS x 1 at 2 ohms)
- 2400 watts
- Class D amp technology
- variable lo
- w-pass filter (40-240 Hz, 12 dB per octave)
- wired remote control adjusts variable bass boost (0-18 dB at 50 Hz)
- preamp inputs and outputs
- speaker-level inputs via supplied RCA-type adapters
- fuse rating: 40A x 3
- 4-gauge power and ground leads recommended — wiring and hardware not included with amplifier
- 13″W x 2-3/8″H x 7-7/8″D
- Mono subwoofer amplifier
- Remote bass boost control
- 19′ Remote cable (RJ-25 plug on both ends)
- Three 40 amp ATO fuses (installed)
- 8″ Speaker-level input adapters
- 3mm Allen wrench
- Four 5/8″ Self-tapping screws
- Two 3/8″ Self-tapping screws
- Owner’s manual (English/ French/ Spanish)
PIONEER AMPLIFIER
- 1000 Watts Max Power
- Automatic signal sensing and Turn-ON
- Variable high pass filter
- Adjustable bass boost
- Product highlights:
- 4-channel car amplifier
- 60 watts RMS x 4 at 4 ohms (95 watts RMS x 4 at 2 ohms)
- 190 watts RMS x 2 in bridged mode (4-ohm stable in bridged mode)
- CEA-2006 compliant
- variable high-pass (40-500 Hz, 12 dB/octave) and switched low-pass (80 Hz, 12 dB/octave) filters on A channels
- switchable high- and low-pass filters (80 Hz, 12 dB/octave) on B channels
- switchable bass boost (0, 6, 12 dB at 50 Hz) on B channels
- preamp and speaker-level inputs
- fuse rating: 25A x 2
- 8-gauge power and ground leads recommended — wiring and hardware not included with amplifier
- 14-1/4″W x 2-3/8″H x 8-1/2″D
- 4-Channel amplifier
- Two 25A ATO fuses (installed)
- Speaker-level input harness with eight 4″ wires
- 4 Self-tapping screws (3/4″ length)
PIONEER AMPLIFIER
- Max Power Input: 160W
- Nominal Input Power: 50W
- Frequency Response: Deep Bass Mode | 20-200Hz
- Frequency Response: Dynamic Bass Mode | 40-160Hz
- Sensitivity: Deep Bass Mode – 95dB
- Sensitivity: Dynamic Bass Mode – 100dB
- Impedance: 1Ohm
- Woofer Material: Aluminium
- Voice Coil Type: Copper Round Wire 4-Layer
- Voice Coil Bobbin Type: Glass Imide
- Lowest Resonance Frequency: 32Hz
- Magnets: Stonium
- Weight: 3.5kg
- Dimensions mm (WxHxD) 280x200x70